Broome-Tioga Demo
V8 Class
All glass, inter. And chrome must be removed from car. This
must be done prior to entering facility.
Gas tank must be removed and placed in back seat.
NO PLATING OF FRAME.
You can use 14, 15, 16 inch tires of any ply DOT only.
Doors can be welded or chained.
Shifter can be removed to the floor.
You can change body mount bolts out up to 1 inch all thread
and you can add 2 bolts to your sub frame.
Can weld body seams outside only using 4 inch wide strap, ¼
inch thick. Doors and trunk.
Can use 6 bolts to hold hood
down, only 2 can be hooked to frame with 5 inch washers ¼ inches thick. Must have two 10 inch holes for fires or cut center of hood
out.
Trunk can also be held down with FOUR 1 inch all thread and
washers can be up to 5 inches ¼ inch thick.
Bumpers can be welded to the frame with a 4 inch by 6 inch by
¼ plate ONLY.
Or can be bolted on, nothing bigger than 1 inch all thread.
Must have two 10 inch holes in
hood or center cut out.
DO NOT paint or undercoat the frame.
If it is painted or undercoated with anything you will not be
inspected.
4 point cage can be used inside drivers
compartment.
Side bars can be no bigger than 2 by 6 channel.
Cross bars can be no bigger than 4 inches.
Can not have down bars to the
floor.
Cross bars can be up to 1 foot behind seat.
No kickers allowed.Engine can be
any make or model change out.
Engine can be welded or chained in original place ONLY.
You may weld you coil springs in your GM’s and Ford’s.
Bumpers can be welded to the frame with a 4 inch by 6 inch by
¼ plate ONLY.
Or can be bolted on, nothing bigger than 1 inch all thread.
Suggested bar or chain
from roof to dash in center of dash.
THERE WILL BE NO
SANDBAGGING ALLOWED IN THIS
IF in the rules it
doesn’t specifically say you can’t, it doesn’t mean you can do it.
Any questions call Broome
Tioga Sports Center (1-607-849-4438)
Broome-Tioga Demo
Youth Class
12-15yrs
old
4-6 Cylinder Only
All glass, interior and chrome must be removed from car.
This must be done prior to entering the facility.
Cars can not be more than 110 inch wheel base.
No AMC Pacers.
BUMPERS MUST BE STOCK
ONLY.
Shifter can be removed to the floor.
Gas tank may be moved to back seat or under car if in front
of axle.
Doors can be welded or chained.
Drivers door can have 2 inch angle across the driver door on the
outside for safety.
It can not exceed 6 inches past door seams and MUST have a
some form of a window screen on drivers door.
Engine can be welded or chained in original place ONLY.
Cross bars must stay behind fire wall and in front of rear
hump or rear deck.
DO NOT paint or undercoat the frame.
Two 10 inch holes or center of hood cut out.
Must have a bar or chain from roof to dash in center of
windshield.
You can change body mount bolts out up to 1 inch all thread
and you can add 2 bolts to your sub frame.
Can weld body seams outside only using 4 inch wide strap, ¼
inch thick. Doors and trunk.
Can use 6 bolts to hold hood
down, only 2 can be hooked to frame with 5 inch washers ¼ inches thick. Must have two 10 inch holes for fires or cut center of hood
out.
Trunk can also be held down with FOUR 1 inch all thread and
washers can be up to 5 inches ¼ inch thick.
Bumpers can be welded to the frame with a 4 inch by 6 inch by
¼ plate ONLY.
Or can be bolted on, nothing bigger than 1 inch all thread.
If it is painted or undercoated with anything you will not be
inspected.
4 point cage can be used inside drivers
compartment.
Side bars can be no bigger than 2 by 6 channel.
Cross bars can be no bigger than 4 inches.
Can not have down bars to the
floor.
Cross bars can be up to 1 foot behind seat.
No kickers allowed.Engine can be
any make or model change out.
You may weld you coil springs in your GM’s and Ford’s.
IF in the rules it
doesn’t specifically say you can’t, it doesn’t mean you can do it.
LETS MAKE THIS A SAFE
THERE WILL BE NO
SANDBAGGING ALLOWED IN THIS
Any questions call Broome
Tioga Sports Center (1-607-849-4438)
Broome-Tioga Demo
Compact
4-6 Cylinder Class
All glass, interior and chrome must be removed from car.
This must be done prior to entering the facility.
Cars can not be more than 110 inch wheel base.
DO NOT paint or undercoat the frame.
No AMC Pacers.
Doors can be welded or chained.
Engine can be welded or chained in original place ONLY
Cars must have stock engines.
Bumpers may be inner changed with any 4 cyl
or V6 car if in front of axle.
Gas tank may be moved to back seat or under car if in front
of axle.
4 point cage can be used.
Cross bars must stay behind fire wall and in front of rear
hump or rear deck.
Tires can be any ply DOT only.
Two 10 inch holes must be cut in hood.
Shifter can be removed to the floor.
You can change body mount bolts out up to 1 inch all thread and
you can add 2 bolts to your sub frame.
Can weld body seams outside only using 4 inch wide strap, ¼
inch thick. Doors and trunk.
Can use 6 bolts to hold hood
down, only 2 can be hooked to frame with 5 inch washers ¼ inches thick. Must have two 10 inch holes for fires or cut center of hood
out.
Trunk can also be held down with FOUR 1 inch all thread and
washers can be up to 5 inches ¼ inch thick.
Bumpers can be welded to the frame with a 4 inch by 6 inch by
¼ plate ONLY.
Or can be bolted on, nothing bigger than 1 inch all thread.
If it is painted or undercoated with anything you will not be
inspected.
4 point cage can be used inside drivers
compartment.
Side bars can be no bigger than 2 by 6 channel.
Cross bars can be no bigger than 4 inches.
Suggested bar or chain from roof to dash in center of dash.
Can not have down bars to the
floor.
Cross bars can be up to 1 foot behind seat.
No kickers allowed.Engine can be
any make or model change out.
You may weld you coil springs in your GM’s and Ford’s.
THERE WILL BE NO
SANDBAGGING ALLOWED IN THIS
IF in the rules it
doesn’t specifically say you can’t, it doesn’t mean you can do it.
Any questions call Broome
Tioga Sports Center (1-607-849-4438)
Broome-Tioga
Demo
Truck Class
All glass, inter. And chrome must be removed from truck.
This must be done prior to entering the facility.
Engine can be welded or
chained in original place ONLY
NO PLATING OF THE FRAME.
Doors can be welded or chained.
Gas tank must be moved into the cab.
If it can not be put in the cab the tank must be covered and
secured in box down.
Shifter can be removed to the floor.
Any stock bumpers no home made bumpers can weld bumpers on but no adding metal.
DO NOT paint or undercoat the frame.
Can run 4x4.
Any DOT tire deemed safe by the event management.
No adding weight.
You can change body mount bolts out up to 1 inch all thread
and you can add 2 bolts to your sub frame.
Can weld body seams outside only using 4 inch wide strap, ¼
inch thick. Doors and trunk.
Can use 6 bolts to hold hood
down, only 2 can be hooked to frame with 5 inch washers ¼ inches thick. Must have two 10 inch holes for fires or cut center of hood
out.
Bumpers can be welded to the frame with a 4 inch by 6 inch by
¼ plate ONLY.
Or can be bolted on, nothing bigger than 1 inch all thread.
If it is painted or undercoated with anything you will not be
inspected.
4 point cage can be used inside drivers
compartment.
Side bars can be no bigger than 2 by 6 channel.
Cross bars can be no bigger than 4 inches.
Can not have down bars to the
floor.
Cross bars can be up to 1 foot behind seat.
No kickers allowed.Engine can be
any make or model change out.
You may weld you coil springs in your GM’s and Ford’s.
Two ten inch holes or
center of hood must be cut out.
Suggested bar or chain
from roof to dash in center of dash.
THERE WILL BE NO
SANDBAGGING ALLOWED IN THIS
IF in the rules it
doesn’t specifically say you can’t, it doesn’t mean you can do it.
Any questions call